Gopro Panoramic Sports Camera 360 Degree VR Top Low Mount Holder Hanging Bracket Fixed Clamp Adapter for DJI Mavic 2 Pro/Zoom
Descripion:
This camera mount support for a variety of installation, can be installed up or down, handheld takeoff and landing.
Two joint design, not only easy to carry but also can adjust the position of the camera.
Easy to install and convenience
3D pringting product The visual positioning system under this bracket is invalid. Novice please take off in good condition of GPS signal.
You must take off and land by hand, and you need to turn off the visual positioning landing ground detection function in DJI GO2. Position: click the three points in the upper right corner -- perception Settings -- advanced Settings
Net weight: 45g
Gross weight: 60g
Product size: 11*7*3cm
Packing size: 14*11*4cm
Material: ABS
Model:For MAVIC 2
Technology: 3D Printing plastic material
packing list:
1 set of Mount Bracket Holder
Note:
does not include the drone
It's a 3D printed product with fine stripes on the surface![](https://ae01.alicdn.com/kf/HTB1FRVURrrpK1RjSZTEq6AWAVXaF.jpg?width=1000&height=1000&hash=2000)
![](https://ae01.alicdn.com/kf/HTB12xXIRzDpK1RjSZFrq6y78VXa8.jpg?width=1000&height=1000&hash=2000)
![](https://ae01.alicdn.com/kf/HTB13rpLRCzqK1RjSZFLq6An2XXa3.jpg?width=1000&height=1000&hash=2000)
![](https://ae01.alicdn.com/kf/HTB1Aj8MRrPpK1RjSZFFq6y5PpXa5.jpg?width=1000&height=1000&hash=2000)
![](https://ae01.alicdn.com/kf/HTB1HsNVRq6qK1RjSZFmq6x0PFXaH.jpg?width=1000&height=1000&hash=2000)
![](https://ae01.alicdn.com/kf/HTB1MCNWRwHqK1RjSZJnq6zNLpXag.jpg?width=1000&height=1000&hash=2000)
![](https://ae01.alicdn.com/kf/HTB1UoefRxjaK1RjSZKzq6xVwXXam.jpg?width=1000&height=1000&hash=2000)
![](https://ae01.alicdn.com/kf/HTB122ieRxnaK1RjSZFBq6AW7VXah.jpg?width=1000&height=1000&hash=2000)
![](https://ae01.alicdn.com/kf/HTB1yDXWRwHqK1RjSZJnq6zNLpXa5.jpg?width=750&height=750&hash=1500)
![](https://ae01.alicdn.com/kf/HTB1lwJYRpzqK1RjSZFvq6AB7VXa8.jpg?width=750&height=750&hash=1500)
![](https://ae01.alicdn.com/kf/HTB1fclLRCzqK1RjSZFLq6An2XXam.jpg?width=750&height=750&hash=1500)
Safety reminder:
1. When using this panoramic camera bracket, you can take off and land by holding the extension rod below, and be sure to tighten the screws to avoid injury caused by loosening and sliding;
2. Two spacers are given as a gift to prevent the screws from loosening in the camera. You can also buy screws and other products to strengthen the screws and prevent the camera from falling.
3. Since panoramic cameras are different, it is suggested that after you get the product, you should first conduct assembly and debugging and low-flying debugging. During debugging, you should be careful to avoid injury or explosion, and then fly normally after stabilization.
4. The novice does not recommend to try to use the 360-degree panoramic camera holder. The store does not bear any Fried chicken and camera falling accidents caused by any reason.